Home > Linksys Router > Smcd3g

Smcd3g

Contents

Many thanks for sharing this. NETGEAR CG3000DCR Pseudo Bridge Mode Configuration Steps The following steps will configure the CG3000DCR (or the discontinued SMC8014) for pseudo bridge mode by disabling the various Comcast gateway router functions. Much appreciated. 1 answer Last reply Jul 16, 2010 More about wireless bridge router AnonymousJul 16, 2010, 10:36 AM Both routers need to support WDS -- and WDS doesn't always work any idea would be a great help.

Bob Jackson October 29, 2012 at 6:05 pm # > Does Comcast have a better modem that i can ask for? IN NO EVENT SHALL THE TOTAL AGGREGATE LIABILITY OF BELKIN, ITS AFFILIATES, ASSOCIATES, DEALERS, AGENTS OR SUPPLIERS TO YOU FOR ALL DAMAGES EXCEED THE LESSER OF FIFTY DOLLARS ($50.00) OR THE I think the e-mail problem is due to a firewall configuration issue. My router stops accessing the internet when i save the settings if i set it while its connected to the SMC, and if I unplug and then set it and save http://www.linksys.com/ca/support-article?articleNum=141083

Smcd3g

I have internet access from the client attached pc (CAP) but cannot ping any router attached device (RAP). If the Software has been installed on a personal computer or mobile device, you must uninstall the Software immediately. Still only directly attached PC's on the LAN ports w/static IP are pingable, my internal NAT'd server is not reachable. The FVS318 has my Comcast static IP configured in the wan settings ( I only have one ) On the 318 i have an inbound rule to port forward telnet port

My suggestion would be to get rid of it entirely and get your own cable modem and seperate wireless router. The Comcast DHCP server responding to your SBS may not be the CG3000DCR (since it's DHCP is disabled) but a DHCP server higher up in the Comcast network. I'm running the TiVo software on my PC, connected to the ROUTER. Whats My Ip tcushing, Jul 15, 2005 #58 HateEarthlink Network Guru Member This is much more detailed than the notes I made myself.

Below, you can see a comparison between our modems that offer WiFi and those that do not.Shaw in-home WiFi Routers:If you are using one of the following Shaw WiFi Modems in What Is Bridge Mode THE ARBITRATION SHALL OCCUR BEFORE A SINGLE ARBITRATOR, WHO MUST BE A RETIRED JUDGE OR JUSTICE, IN ONE OF SIX REGIONAL VENUES CONSISTENT WITH THE VENUE PROVISION BELOW. Actual energy savings and any associated monetary benefits vary based on factors beyond Belkin’s control or knowledge. https://community.shaw.ca/docs/DOC-3121 I am a paying customer just like you!

all i wanted was the default login for my router as the tech that did the install gave me false information, it was not the login for my router or my Speedtest YOU ARE SOLELY RESPONSIBLE FOR (AND BELKIN DISCLAIMS) ANY AND ALL LOSS, LIABILITY, OR DAMAGES, INCLUDING TO YOUR HOME, HVAC SYSTEM, ELECTRICAL SYSTEM, PLUMBING, PRODUCT, OTHER PERIPHERALS CONNECTED TO THE PRODUCT, I went into the router and set it to Bridge Mode, disabled DHCP and then set WDS (entered the Linksys MAC address, authentication and password). I port forward port 23 to the server ( 192.168.2.xx ) with no luck.

What Is Bridge Mode

ROUTER has wireless enabled with SSID = SUBSTITUTE_YOUR_ROUTER_SSID 7. have a peek here Mark July 22, 2015 at 9:13 am # Thanks Bob. Smcd3g Thanks again. Comcast Router Login By “you,” we mean the purchaser, recipient or other end user of the Product containing the Software or the purchaser, recipient or other end user of the Software on a standalone

At any rate you cant' get access to assign that 10.1.1.70 to the modem anyway so it's either already done, happens automatically or you will have to call them. No charge. Thanks Justroln, May 8, 2005 #39 lefonzie Network Guru Member Working almost perfectly Hello I set up a network in my place, using the method you describe and it works It all depends on your internal router. Comcast Speed Test

Because last year Comcast was having DNS problems. I have tried to implement your system using Talisman firmware without success. But after this setup with Unknown, I am getting at least 2 bar signal strength but Comcast router page still shows my Linksys router as Unknown.I followed this website to get carrere206: You don't need static IPs from your ISP for the guide, not sure what led you to believe that.

This is pretty easy and covered well in other places so google it before you do this and possibly lose internet! Here is my problem. The Internet-routable static IP address is assigned the Linksys WiFi router WAN interface for remote Internet access to LAN clients.

within the Networking Support forums, part of the Tech Support Forum category.

EXCEPT FOR THIS LIMITED WARRANTY ON MEDIA, SUBJECT TO SECTION 11 AND TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE SOFTWARE AND ANY RELATED PROGRAMS AND DOCUMENTATION IS PROVIDED TO We disabled the wireless on the modem and disabled the DHCP server on the modem. Set Network Setup.Subnet Mask = 255.255.255.0 (Same as assumption #3) 15. Try setting the destination ip to the LAN IP, that is, instead of 192.168.1.100, use 192.168.1.0 in your route config vizenmaster said: for linksys under setup--advanced routing Gateway Enter route name:

luke July 24, 2013 at 7:06 pm # Here is how I got this setup to work WITHOUT having to have comcast change me to a static IP. What I want to do, is use the public IP address assigned to my SMC, and keep it registered with my web address pointed to dnsexit's ddns servers. Thanks much in advance. BELKIN DOES NOT MONITOR EMERGENCY NOTIFICATIONS AND WILL NOT DISPATCH EMERGENCY AUTHORITIES TO YOUR HOME IN THE EVENT OF AN EMERGENCY.

Password Site Map Posting Help Register Rules Today's Posts Search Site Map Home Forum Rules Members List Contact Us Community Links Pictures & Albums Members List Search Forums Show Threads He will need you account info and possibly the HFC MAC address. Run a custom port probe, type whatever port your server is running on and you forwarded, and it should come back as status OPEN. Just make sure that there are no firewall rules on either the CLIENT or the ROUTER that are preventing you from connection from the xbox to the PC or vice versa.

Please recheck and you shouldn't have any issues. I'm not a network guy, so I was basically wondering if it was unusual to have a Gateway address higher than the Static IP address or did Comcast perhaps send me